|Embankment Slides are a fun way to move down a slope. Safety is important, we don't want Jack and Jill "tumbling" down the hill, but safely sliding! Hillside, embankment or slope slides are NOT terribly complicated, but do take some planning to ensure that safety, form and function all meet together at the end. An embankment slide is a good way to introduce a long bedway slide into a play area without the risk of steps, ladders, decks and fall heights.|
|EMBANKMENT SLIDES BY DECK HEIGHT (click your height below)...|
There are some critical measurements when designing your slide. You will need to know:
1. the DECK HEIGHT or elevation of the entrance: This is the industry term for the height of the hill. This can be somewhat difficult to measure when there is a hill beneath your feet. Is is probably not possible to drop a plumb-bob down or measuring tape to determine how high up you are. There are some fancy and expensive devices that utilize GPS to determine elevation, such as above or below sea level. Many of these do not have accuracy within a few feet, so this is not usually the best tool to utilize. Landscaping plans or architectural plans may have this number recorded already. We can reverse engineer the numbers to determine height if you know SLOPE and LENGTH.
2. the ANGLE or slope amount: Too steep of a slide and the passenger will descend too rapidly, obviously with risk and danger involved. Too shallow of an angle and the passenger may not reach the end. While there may not be a high fall to the ground from spills overboard, we want to ensure that the ride is safe an successful. The angle and slope is prescribed by safety standards. Slides for toddlers average 24 degrees or less. Slides for toddlers should be no steeper than 30 degrees. Many designs may include sections with higher angles up to 35 degrees. No portion of a slide or slide path should ever exceed 50 degrees!
3. the LENGTH of the slide bedway: The height, length and slope are always factors that relate to each other. Many times you will know how long you want your slide to be. We can reverse engineer the numbers to determine the length if you know HEIGHT and ANGLE. Remember to allow proper room at the exit of the slide, with safety surfacing on the ground to have a safe "use zone" at the end. For "quick" math, the length is roughly DOUBLE the deck elevation. Thus a 7' deck height slide would be 14' long. This isn't the exact ratio or formula, your slide may be longer or shorter.
4. the slide shape or design: With a hill slide or embankment slide, the general concept is 'down.' For more fun you may want or need to veer to one direction, or introduce more of a winding "snake slide" path. Your final design will consider the shape and path with features implemented to enhance safety. A flat bedway with low side rails will be less expensive, but a tube or trough slide with a covered or deep bedway will work harder to contain the passenger where they are supposed to be. Turns may be introduced to reduce the passenger speed. Too many or too much of a turn and the passenger may go 'overboard.' Wide bedways may be considered for short distances. Longer distances suggest straight and narrow.
5. the quality of the slide: While "cheap" is good for the budget, price should not be your primary focus for your slide. The longer you make your slide, the higher the cost of materials and freight to get the slide to your location. Residential grade slides, backyard slides or playset slides are typically made from a different process that doesn't hold up well to constant use. Heavy duty, commercial grade plastics are thicker and joints or sections will bolt together more securely. Plastic thickness, deliberate design features to molded components, UV stabilizers and treatment for static discharge are important features found only in commercial grade slide. Metal slides, including aluminum slides and stainless steel slide will include greater strength and durability for long term use of your slide.
|How to Measure for your Slide|
1. Identify the area for the slide. You may need to consult a professional to stabilize the area to prevent unintended movement.
2. A photograph is a helpful tool that helps us to see the site through your eyes. Your landscaper, architect, builder, contractor or engineer may have already prepared a sketch of the site.
3. Mark the area intended for the slide. Measure the distance from the point at the high end, down to the exit at the low end. Measure the area and space forward of the exit of the slide that will be the safety perimeter or use zone.
4. Perhaps the most confusing step in planning is the measurement or calculation of the slope. Fortunately, there are free and low cost applications avaialble for smart phones and tablets (IOS and Android) that will help you determine slope. A 5" device on a 30' hill side is going to yield unreliable results. Using a long, flat and straight board, place the board on your hillside. Now place your phone or tablet on the board. Obtain measurements throughout the descent of the area for your slide previously marked. Using visual clues you may see areas that have distinctly different angles or slopes. With a table of measurements, we can create a "slope" using the recorded findings, and graph or draw this to paper.
5. SHARE your findings. With your goals in mind and your recorded findings, we will guide you the rest of the way...